WEBVTT

1
00:00:00.400 --> 00:00:02.480
This video
will demonstrate how

2
00:00:02.480 --> 00:00:05.610
to install a combination
of small and large

3
00:00:05.610 --> 00:00:07.110
wall-mounted cabinets.

4
00:00:07.980 --> 00:00:10.680
Only install these
cabinets into wooden wall

5
00:00:10.680 --> 00:00:13.380
studs covered by drywall
or sheetrock.

6
00:00:14.080 --> 00:00:16.030
Securely mounting
the hanging rails

7
00:00:16.030 --> 00:00:18.380
is critical for a proper
installation.

8
00:00:19.110 --> 00:00:21.140
Before you begin, make
sure you

9
00:00:21.140 --> 00:00:23.340
have the following tools
and hardware.

10
00:00:23.810 --> 00:00:27.080
Stud finder, power
screwdriver or drill,

11
00:00:27.480 --> 00:00:31.900
3 16th inch drill bit,
pencil, tape measure,

12
00:00:32.210 --> 00:00:33.780
level, hacksaw.

13
00:00:34.600 --> 00:00:36.600
Each cabinet
comes with one

14
00:00:36.600 --> 00:00:38.810
38-inch metal
hanging rail,

15
00:00:39.160 --> 00:00:41.990
one connecting brace,
three wood screws,

16
00:00:42.320 --> 00:00:44.800
an Allen key,
and an Allen key bit.

17
00:00:45.620 --> 00:00:48.130
The metal hanging rails
are designed to prevent

18
00:00:48.130 --> 00:00:50.720
cabinets from sliding
past the end of the rail.

19
00:00:51.620 --> 00:00:54.630
During assembly,
you attach two or three

20
00:00:54.630 --> 00:00:56.180
metal rail hooks
to the back

21
00:00:56.180 --> 00:00:57.560
of your cabinet.

22
00:00:57.560 --> 00:00:59.780
These fasten onto
the metal rail

23
00:00:59.780 --> 00:01:01.280
when mounted.

24
00:01:01.700 --> 00:01:04.820
When using multiple rails,
a connecting brace

25
00:01:04.820 --> 00:01:08.310
is fastened across two
adjoining rails to provide

26
00:01:08.310 --> 00:01:10.500
additional support
between studs.

27
00:01:11.250 --> 00:01:13.690
It is designed for use
with wooden studs

28
00:01:13.950 --> 00:01:16.950
positioned 16 inches
apart on center.

29
00:01:18.280 --> 00:01:21.130
Start by hanging the rails
for the large cabinets.

30
00:01:22.230 --> 00:01:24.690
In our installation,
we want the bottom

31
00:01:24.690 --> 00:01:27.700
of the tall storage
cabinets to be 12 inches

32
00:01:27.700 --> 00:01:29.200
from the floor.

33
00:01:29.280 --> 00:01:32.230
At multiple locations
along the wall, measure

34
00:01:32.230 --> 00:01:35.210
79 1⁄2 inches
from the floor

35
00:01:35.360 --> 00:01:36.860
and make a mark.

36
00:01:37.120 --> 00:01:40.490
Using a level, draw a line
to connect the marks.

37
00:01:42.330 --> 00:01:44.480
Studs are typically 16
inches

38
00:01:44.480 --> 00:01:46.200
apart center to center.

39
00:01:47.050 --> 00:01:49.980
To find the studs,
move the stud finder

40
00:01:49.980 --> 00:01:52.200
along the wall until you
hear a tone.

41
00:01:53.050 --> 00:01:56.060
Continue along the wall
until the tone stops.

42
00:01:56.680 --> 00:01:58.690
Mark the center
between the beginning

43
00:01:58.740 --> 00:02:01.160
and end of the tone
with a vertical mark.

44
00:02:03.500 --> 00:02:07.320
Pre-drill 3-inch deep
holes where the horizontal

45
00:02:07.320 --> 00:02:08.820
and vertical lines meet.

46
00:02:10.800 --> 00:02:14.030
Position the metal track
over the pre-drilled holes

47
00:02:14.500 --> 00:02:17.760
and insert wood screws
into the first and second

48
00:02:17.760 --> 00:02:19.920
holes with the Allen key
provided.

49
00:02:20.300 --> 00:02:23.150
For faster installation,
use a drill

50
00:02:23.240 --> 00:02:25.110
and the supplied hexagonal
bit.

51
00:02:26.150 --> 00:02:28.490
Position the connecting
brace so that it

52
00:02:28.490 --> 00:02:31.280
overlaps the last hole
on the first metal rail.

53
00:02:32.500 --> 00:02:35.010
Insert the remaining screw
through both

54
00:02:35.010 --> 00:02:37.280
the connecting brace
and the metal rail.

55
00:02:38.170 --> 00:02:41.100
Slide the second metal
rail behind the connecting

56
00:02:41.100 --> 00:02:44.040
brace and position
it next to the first rail.

57
00:02:44.730 --> 00:02:47.350
Secure the connecting
brace to the second rail.

58
00:02:48.060 --> 00:02:50.490
Repeat these steps to hang
additional rails

59
00:02:50.490 --> 00:02:51.990
and braces.

60
00:02:52.620 --> 00:02:54.560
Installing the cabinets
with outdoors

61
00:02:54.560 --> 00:02:56.990
attached makes it
easier to lift them

62
00:02:56.990 --> 00:02:58.490
into position.

63
00:02:58.620 --> 00:03:00.510
With two people,
carefully

64
00:03:00.510 --> 00:03:03.590
lift the tall cabinet
so that the hooks are just

65
00:03:03.590 --> 00:03:06.680
above the rail,
then carefully lower onto

66
00:03:06.680 --> 00:03:07.950
the rail.

67
00:03:07.950 --> 00:03:10.750
The smaller wall cabinets
can be lifted into place

68
00:03:10.750 --> 00:03:12.250
by one person.

69
00:03:13.450 --> 00:03:16.090
We want the bottom edge
of the lower cabinets

70
00:03:16.260 --> 00:03:17.980
to line
up with the bottom edge

71
00:03:17.980 --> 00:03:20.510
of the tall cabinets
at 12 inches

72
00:03:20.510 --> 00:03:21.970
from the floor.

73
00:03:21.970 --> 00:03:26.390
In two places, measure
31.5 inches from the floor

74
00:03:26.480 --> 00:03:27.980
and mark.

75
00:03:28.030 --> 00:03:31.330
With a level, draw a line
to connect the marks.

76
00:03:32.270 --> 00:03:34.490
Pre-drill three inch
deep holes

77
00:03:34.530 --> 00:03:36.850
where the horizontal
and vertical lines meet.

78
00:03:38.360 --> 00:03:40.940
Since the hanging rail
is longer than the space

79
00:03:40.940 --> 00:03:42.490
needed
for the lower cabinet,

80
00:03:42.930 --> 00:03:45.230
we have used a hacksaw
to cut the rail

81
00:03:45.230 --> 00:03:47.860
one fourth of an inch
smaller than the cabinet

82
00:03:47.860 --> 00:03:48.890
width.

83
00:03:48.890 --> 00:03:52.420
In this case,
29 3 fourths inches

84
00:03:52.560 --> 00:03:54.440
for a 30 inch
wide cabinet.

85
00:03:55.220 --> 00:03:58.390
Position the metal track
over the pre-drilled holes

86
00:03:58.540 --> 00:04:01.300
and insert wood screws
with the Allen key

87
00:04:01.430 --> 00:04:03.550
or hexagonal bit provided.

88
00:04:04.180 --> 00:04:06.800
Leave an eighth of an inch
gap between the hanging

89
00:04:06.800 --> 00:04:08.300
rail and tall cabinet.

90
00:04:09.260 --> 00:04:10.810
Hang the remaining
cabinets,

91
00:04:10.950 --> 00:04:12.880
then insert drawers,
shelves,

92
00:04:12.930 --> 00:04:14.430
and attached doors.

93
00:04:14.580 --> 00:04:17.010
Door hinges can be
adjusted six ways.

94
00:04:17.940 --> 00:04:20.920
For horizontal adjustment,
turn the adjustment

95
00:04:20.920 --> 00:04:23.530
screw counterclockwise
to move the door

96
00:04:23.530 --> 00:04:24.760
to the left.

97
00:04:24.760 --> 00:04:27.140
Turn it clockwise to move
the door to the right.

98
00:04:28.190 --> 00:04:30.380
To move the door forwards
or back,

99
00:04:30.650 --> 00:04:33.620
loosen the fixing screw
and shift the location

100
00:04:33.620 --> 00:04:35.000
of the hinge.

101
00:04:35.000 --> 00:04:37.760
For vertical adjustment,
loosen the hinge plate

102
00:04:37.760 --> 00:04:40.220
screws and adjust door up
and down.

103
00:04:41.240 --> 00:04:43.100
With your installation
complete,

104
00:04:43.510 --> 00:04:46.250
fill your cabinets
with tools, yard supplies,

105
00:04:46.300 --> 00:04:48.180
sports equipment,
and other items

106
00:04:48.180 --> 00:04:49.040
in your garage.